Pre-milling device: ◆ With built-in soot blowing device, milling one layer first to make the board smoother and the edge sealing more close
Gluing device: ◆One of the glue pots uses a high-efficiency glue pot, which is more stable and less likely to overflow.
◆The glue coating and tape feeding device adopts a knurled needle wheel structure, which makes the tape feedingsmoother.
◆The distance between the guide plate and the glue coating device is controlled at about 0.1mm to ensure the quality of glue coating.
End cutting device: ◆45 degree precision linearguide structure.
◆Two 0.37kw motors, speed:12000rpm.
◆Adopt frequency converter control
Rough trim device: ◆Two motors, each with a power of 0.75kw high-speed
motor.
◆Two roughing milling cutters.
◆Equipped with independent dust cover
Fine trim device: ◆Two motors, each with a power of 0.75kw high-speedmotor.
◆Two finishing milling cutters, specifications: (arc radiusR1.5).
◆Equipped with digital hand wheel to adjust trimming thickness
◆Equipped with independent dust hood.
Scraping device: ◆Scraper blade radius R1.5.
◆Equipped with digital hand wheel to adjust scrapingthickness.
◆Equipped with electronic pneumatic control blowing
Machine Configuration
How an Automatic Edge Banding Machine Works (8 Steps)
- Pre-milling — mills the panel edge flat for a seamless glue joint.
- Gluing — applies PUR hot-melt glue evenly along the panel edge.
- Edge feeding & pressing — feeds PVC/ABS/veneer tape and presses it onto the glued edge.
- End trimming — cuts the front and rear excess tape flush with the panel.
- Rough & fine trimming — trims top and bottom tape overflow to a smooth radius.
- Corner rounding — rounds the two ends of the edge for safety and appearance.
- Scraping — scrapes the trimmed edge to remove residual glue lines.
- Buffing — polishes the edge to a clean, glossy finish.
Edge banding machine 468JL Glue Type: PUR
PUR hot-melt glue gives a stronger, heat- and moisture-resistant bond — ideal for kitchen, bathroom, outdoor and high-humidity panels.
Key Parameters
- Panel thickness: 10-60mm
- Feeding speed: 15, 18, 23m/min
- Working air pressure: 0.7Mpa
Price Range
Typical ex-works price for this class of machine: $15,000 – $40,000. Final price depends on configuration, voltage and shipping; contact Leabon for a confirmed quotation.
Frequently Asked Questions
- Q: What is an automatic edge banding machine used for?
- A: It seals the exposed edges of panels (MDF, plywood, particleboard, melamine) with PVC, ABS or veneer tape so the board core is protected from moisture and impact, and the furniture looks clean and finished.
- Q: PUR vs EVA hot-melt glue — which should I choose?
- A: EVA is economical and covers most cabinet and furniture work. PUR hot-melt glue gives a stronger, heat- and moisture-resistant bond — ideal for kitchen, bathroom, outdoor and high-humidity panels. This model is supplied with PUR as standard.
- Q: What panel and edge-band sizes can it handle?
- A: Typical range: Panel thickness: 10-60mm; Feeding speed: 15, 18, 23m/min; Working air pressure: 0.7Mpa. See the full specification table on this page for the exact model figures.
- Q: How fast is the production line?
- A: Feeding speed is around 15, 18, 23m/min depending on panel profile and glue type, supporting continuous panel-by-panel output for factories.
- Q: Do you provide installation, training and warranty?
- A: Yes. Leabon provides overseas on-site installation, operator training and a 12-month warranty with spare-parts support, so your line runs reliably from day one.
