Product Features
Designed for 45-degree beveled edge banding：bevel pre-milling, bevel gluing, oblique-and-straight pressing, fine trimming, end cutting, scraping, edge-band slotting, lamp pre-heating, then polishing and cleaning. Uses internationally renowned brand electrical appliances, including Delta PLCs, Siemens appliances, etc. More product videos: https://www.youtube.com/@IleabonProcess Features
Bevel Pre-milling
Mills the 45° bevel into a clean, dust-free gluing surface so mitered corners close tightly with no step.
Lamp Pre-heating
Pre-heats the panel with IR lamps so hot-melt glue bonds faster and stronger, even in cold workshops.
Bevel Edge Gluing
Applies an even glue layer along the 45° bevel via a dedicated angled gluing head — not a retrofitted straight one. It is independent from the straight-edge gluing unit, so one machine covers both bevel and standard edges.
Edge Band Slotting
Cuts lighting/decorative grooves into the edge band in-line — ideal for lit display cabinets and wall units. 1
Oblique & Straight Pressing
Presses the band onto both bevel and straight edges with even pressure for a flush, bubble-free bond.
Cleaning
Add cleaning section, wipes off residual glue and wax so the edge is clean before polishing.
OUR CERTIFICATES
How an Automatic Edge Banding Machine Works (8 Steps)
- Pre-milling — mills the panel edge flat for a seamless glue joint.
- Gluing — applies EVA hot-melt glue evenly along the panel edge.
- Edge feeding & pressing — feeds PVC/ABS/veneer tape and presses it onto the glued edge.
- End trimming — cuts the front and rear excess tape flush with the panel.
- Rough & fine trimming — trims top and bottom tape overflow to a smooth radius.
- Corner rounding — rounds the two ends of the edge for safety and appearance.
- Scraping — scrapes the trimmed edge to remove residual glue lines.
- Buffing — polishes the edge to a clean, glossy finish.
LZJ-F45 45 Degree Bevel Edge Banding Machine Glue Type: EVA
EVA hot-melt glue is the cost-effective standard for most furniture and cabinet production; PUR is available on request for high-humidity or heavy-duty use.
Key Parameters
- Panel thickness: 15-40mm
- Edge band thickness: Pvc 0.3-1.2mm
- Feeding speed: 0-23m/min
- Working air pressure: 0.7Mpa
Price Range
Typical ex-works price for this class of machine: $8,000 – $20,000. Final price depends on configuration, voltage and shipping; contact Leabon for a confirmed quotation.
Frequently Asked Questions
- Q: What is an automatic edge banding machine used for?
- A: It seals the exposed edges of panels (MDF, plywood, particleboard, melamine) with PVC, ABS or veneer tape so the board core is protected from moisture and impact, and the furniture looks clean and finished.
- Q: PUR vs EVA hot-melt glue — which should I choose?
- A: EVA is economical and covers most cabinet and furniture work. EVA hot-melt glue is the cost-effective standard for most furniture and cabinet production; PUR is available on request for high-humidity or heavy-duty use. This model is supplied with EVA as standard.
- Q: What panel and edge-band sizes can it handle?
- A: Typical range: Panel thickness: 15-40mm; Edge band thickness: Pvc 0.3-1.2mm; Feeding speed: 0-23m/min. See the full specification table on this page for the exact model figures.
- Q: How fast is the production line?
- A: Feeding speed is around 0-23m/min depending on panel profile and glue type, supporting continuous panel-by-panel output for factories.
- Q: Do you provide installation, training and warranty?
- A: Yes. Leabon provides overseas on-site installation, operator training and a 12-month warranty with spare-parts support, so your line runs reliably from day one.
